Adding a BESS to an Existing DG and Synchronisation Panel: Changeover, Interlocks and Protection
Adding a battery to a plant that already has a diesel set and a synchronisation panel is mostly a control and protection job, not a power job. The busbars, breakers and cables usually cope; what has to be rewritten is the changeover logic, the source-selection interlocks, the reverse power and island protection, and the rule deciding which source holds frequency at any instant.
That matters because the existing panel was built around two sources and one assumption — the grid is the reference, and the DG takes over when the grid goes away. Storage breaks it, because a power conversion system can either follow a reference or create one, and it absorbs power as readily as it delivers it. An AMF scheme that has run for fifteen years without complaint will do something unhelpful the first time a battery pushes current into a lightly loaded diesel set. Decide the behaviour on paper first.
What changes when a battery arrives next to a diesel set
Three things change, and the rest of this article follows from them.
A PCS is bidirectional. It exports to the bus and imports from it within milliseconds. A diesel set cannot absorb power, so the moment both are on one bus you need a rule that stops the battery charging from the generator unless you want it to.
A PCS can be a voltage source or a current source. Grid-following, it injects current into a bus whose voltage and frequency somebody else defines; grid-forming, it defines them itself. For protection purposes those are two different machines, and the mode is a procurement decision, not a commissioning setting.
A PCS has almost no short-circuit capability. An alternator delivers several times rated current into a fault and a transformer far more, while a converter typically limits to approximately 1.1 to 1.5 times rated current and holds there. Breakers relying on magnetic trip will not see what they expect.
The first usually gets handled, the second is assumed rather than specified, the third is found at commissioning. Settle all three before the PCS is ordered.
Grid-following or grid-forming: the decision that sets everything else
A grid-following PCS needs an external voltage and frequency reference and cannot run an island on its own. A grid-forming PCS creates the reference itself, can black start, and can hold an island with no grid and no DG.
| Question | Grid-following | Grid-forming |
|---|---|---|
| Needs grid or DG running | Yes, always | No |
| Can black start a dead bus | No | Yes, if specified |
| Load sharing with a DG | kW setpoint control | Droop matched to the governor |
| Protection consequence | Moderate | Needs an island settings group |
| Usual industrial use | Peak shaving, grid-tied | Diesel-off and backup |
The common mistake is a specification that asks for diesel-off operation while the commercial offer quotes a grid-following unit, because the two sit in different paragraphs of one document. If the plant wants to shut the set down and keep running, the PCS must form the grid.
The operating states you must define before touching the panel
Write the state table before anyone draws a schematic. Each row is a mode the plant can be in, and each answers one question: which source holds frequency?
| State | Grid | DG | PCS mode | Holds frequency | Battery may |
|---|---|---|---|---|---|
| Normal | On | Off | Following | Grid | Charge or discharge |
| Outage, DG running | Off | On | Following, kW limited | DG | Discharge only |
| Outage, DG off | Off | Off | Forming | PCS | Discharge only |
| Battery fault | Any | Any | Off, isolated | Grid or DG | Neither |
Fill the last column honestly and then hard-wire it. "Charge only" and "discharge only" are permissives, not preferences, and each belongs on a contact into the PCS run-enable input rather than only in a register the energy management system is meant to write. The row that causes most argument is "outage, DG running": plants want the battery to assist the set so a smaller DG carries the load, which is sound — and is exactly where an unguarded battery charges itself from diesel fuel.
Changeover philosophy: open transition, closed transition, or none
Open transition means the bus is dead for a short interval during the transfer — typically a few hundred milliseconds with contactors, longer with breakers — so contactor-held starters drop out. Closed transition means the sources are paralleled briefly, commonly for approximately 100 to 500 milliseconds, before the outgoing source opens. It needs synchronising, and where the grid is one of the two, the licensee's agreement.
A grid-forming PCS adds a third option: the battery holds the bus while the DG starts, so motors never see a dead bus.
In our panel work the open-transition schemes that cause trouble are those where the dead time was chosen for the switchgear and never checked against the process. A 150 millisecond break is irrelevant to a lighting board and fatal to a vacuum pump holding a reaction under inert gas. List the contactor-held loads and size the transfer around the worst of them, not around the panel.
How a PCS synchronises to a running DG
The mechanics are familiar from any two-set synchronising panel: the incoming source must match the running bus in voltage, frequency, phase sequence and phase angle before its breaker closes. A check-synchronising relay typically supervises a voltage difference of approximately 5 to 10 percent, a slip of approximately 0.1 to 0.3 Hz and a phase angle of approximately 5 to 15 degrees, with a closing-time advance so contacts make near zero angle.
What differs is who adjusts: a diesel set is brought into step by its governor and AVR over several seconds, a PCS in software within about a second. That is why the scheme must name the reference explicitly. If two devices try to synchronise to each other at once you get a slow oscillation that looks like a fault and is actually an argument.
The sequence we specify is: establish the reference, prove dead-bus or live-bus state through hard-wired auxiliary contacts, enable one synchroniser at a time, and permit the close only through a check-sync contact in series with the close circuit. That series contact is what people drop when they decide the synchroniser's own output is good enough. We do not accept it — a check relay exists to be a second opinion.
Load sharing: droop, and why two isochronous sources fight
Droop means a source lets frequency fall slightly as it takes more real power, so several sources settle at a common frequency and divide load in proportion to rating. Isochronous means a source holds frequency exactly at setpoint and takes whatever load that requires.
Two isochronous sources on one bus will fight. Neither accepts a frequency error, so one takes everything and the other unloads or reverses — true of two diesel sets, and of a diesel set beside a grid-forming PCS.
Two arrangements work:
- DG isochronous, PCS in kW setpoint control. The engine holds frequency, the battery delivers a commanded kW. The usual answer for a grid-following PCS beside a DG.
- Both on droop, matched. A diesel governor typically runs at approximately 3 to 5 percent droop; setting the PCS to the same figure divides load by rating, which is what lets a smaller set carry a larger load with battery help.
Reactive power needs the same treatment: voltage droop of approximately 2 to 5 percent on both, or they will circulate reactive current between themselves with nothing to show for it.
We have built and tested a long line of diesel synchronising panels, and the commonest site complaint is unequal kW sharing between two nominally identical sets. It is almost never the alternator — it is a governor droop setting that does not match, or a load-sharing line nobody calibrated. Add a converter and the mismatch becomes far less forgiving, because it responds in milliseconds and the engine in seconds.
Reverse power: the protection that matters most in a retrofit
Reverse power protection, ANSI function 32, trips a generator that starts absorbing real power from the bus instead of delivering it. Motoring a diesel engine drives it as a compressor against no fuel, which is mechanically damaging. For a diesel alternator the element is typically set at approximately 5 to 10 percent of rated power with a delay of a few seconds. A steam set is set differently; do not borrow the number.
The retrofit risk is specific. The DG runs an outage at light load; the energy management system sees a low state of charge and calls for charging; the PCS begins importing; the set unloads, then reverses. If the relay is present and correctly set the DG trips and the plant goes dark — a protection success that feels like a failure. If the element is absent, missing a CT or set at a turbine value, the engine motors.
Verify the element on every retrofit instead of assuming it is enabled, because on older panels we have repeatedly found function 32 available in a numerical relay and never configured. Then prevent the condition rather than relying on the trip: a hard-wired DG-running contact removes the charge permissive. The relay is the last line. The interlock is the design.
Running DG-off: when the set can actually be shut down
Diesel-off is the application most plants want and the one most often under-specified. Four conditions must hold.
- The PCS is grid-forming and rated for the full island load, motor starting included.
- The usable stored energy covers the run time at the state of charge the system actually sits at, not the nameplate.
- The island's inrush is survivable. A converter limited to approximately 1.2 times rated current cannot start a large direct-on-line motor the way an alternator can.
- The protection has a second settings group for island operation.
Point three is where schemes fail on paper. We ask for the island load list and the largest motor's starting method before discussing PCS rating at all, because one uncontrolled start can size the converter for you.
Protection coordination with a current-limited source
Your grading study was done for the transformer and the DG. Redo it for three cases: grid connected, DG connected, and island on the converter alone. Instantaneous and magnetic trips that work on grid fault levels do nothing in the island. Earth fault protection becomes the main discriminating element for single-phase faults, which makes earthing a protection decision rather than a safety formality. Undervoltage tripping with time grading may be needed, and the DC side needs its own study and breaking capacity, a battery being a source of very low internal impedance.
The settings group must switch with the island breaker through a hard-wired contact; running island operation on grid-connected settings leaves faults uncleared while the converter quietly current-limits. How we build the DC and AC distribution around a converter is set out in BESS electrical panel design.
Which interlocks must be hard-wired, and which may live in software
This is the section we argue about most with integrators. Our position: anything whose failure damages machinery, energises something unexpectedly or endangers a person goes in copper. Optimisation and reporting live in software.
| Function | Our position | Why |
|---|---|---|
| Grid, DG and coupler source selection | Hard-wired | Closing two unsynchronised sources must be impossible, not unlikely |
| Check-sync contact in the close circuit | Hard-wired | An independent second opinion on every parallel close |
| DG-running removes the charge permissive | Hard-wired | Prevents charging from diesel, and the reverse power event behind it |
| Island breaker position to settings group | Hard-wired | Protection must follow topology, not a command |
| Battery DC isolation on a BMS or fire trip | Hard-wired | Safety trips never depend on a link |
| Emergency stop | Hard-wired | Must act with the controller powered down |
| Dead-bus close arbitration | Hard-wired | Only one source may close onto a dead bus |
| Export limit | Backstop in copper, setpoint in software | Protection in copper |
| kW, kVAr, state of charge, schedules, alarms | Software | Economic, not safety |
The argument against is that a modern controller is reliable and copper is inflexible. Both are true. The question is what happens in the ten seconds after the controller stops responding, and that answer must not depend on the controller. The same reasoning drives source selection in any two-incomer board, which we set out in 2 incomer and bus coupler interlocking.
Neutral and earthing: what a retrofit usually misses
A transformer and a DG are already two separately derived sources, each with a neutral earth, and a PCS with an isolation transformer commonly adds a third. Three neutral earths give fault current several return paths, which desensitises earth fault relays and circulates current through the earth system under normal load. Decide explicitly whether the interface transformer's star point is earthed, whether that earth is switched or solid, and whether earth fault relays stay selective with three sources instead of two. The common mistake is leaving the new star point solidly earthed because that is how it arrived.
What to change in the existing panel, and what to add
| Item | Typical disposition |
|---|---|
| Existing ACBs and busbar | Retain if the fault rating still covers the new configuration |
| Synchroniser and governor interface | Retain, re-verify settings and calibration |
| Reverse power element | Verify, configure and test — often found unconfigured |
| Source-selection interlocks | Rewire to include the PCS as a third source |
| Relay settings | New island settings group, switched by hard contact |
| Metering | Add bidirectional metering at the PCS feeder |
| PCS feeder and battery DC side | New, with their own protection and isolation |
| Neutral arrangement | Confirm pole count and star-point earthing |
| Control supplies and panel heat load | Recheck both |
On an old board the honest answer is sometimes replacement rather than modification, where the assembly has no design verification evidence or the fault rating is marginal. We would rather say so at quotation stage than during an outage, and that trade-off is covered in old ACB retrofit vs panel replacement.
Prove the logic on the factory floor first. In our FAT practice for synchronising panels we simulate every row of the state table with auxiliary contacts, force each interlock to fail deliberately to confirm the breaker does not close, and record each test by number. Three days of that at our works in Vadodara costs less than one unplanned shutdown at site, and the same discipline across the 17 industrial projects we have delivered across India is what keeps a handover short. What belongs in that document is set out in our electrical panel FAT and routine test checklist.
The governing principle
One source holds frequency at any instant, and the rule deciding which one must be written down, agreed, and wired in copper wherever getting it wrong breaks something.
A battery does not complicate a diesel installation by adding a third box. It complicates it by adding a source that runs backwards, responds faster than an engine and can create a grid of its own. Specify which of those you intend to use, define the states, and let the panel follow the table.
Frequently Asked Questions
Can a BESS be added to an existing DG synchronisation panel?
Usually yes. Busbars, breakers and cables are often adequate, and the work concentrates in the changeover logic, the interlocks, the protection settings and the metering. The checks that decide feasibility are whether the assembly's fault rating still covers the new configuration, and whether the relays can hold a second settings group for island operation.
Does the PCS need to be grid-forming to work with a diesel generator?
No, not for parallel operation. A grid-following PCS can run alongside a DG using the generator as its voltage and frequency reference, delivering a commanded kW. Grid-forming is required only if the battery must hold the bus with both the grid and the DG off, which is what diesel-off and black start mean.
What stops the battery charging from the diesel generator?
A hard-wired DG-running contact that removes the charge permissive from the PCS. Left to a software setpoint, a controller fault or a mis-set schedule can draw battery charge from diesel fuel, the most expensive energy on site. Our recommendation is a physical contact into the PCS run-enable input, with the software permissive in addition rather than instead.
What is reverse power protection and why does it matter more with a battery?
Reverse power protection, ANSI 32, trips a generator that begins absorbing real power from the bus rather than supplying it, because motoring a diesel engine is mechanically damaging. It matters more with storage because a bidirectional converter can create that condition within milliseconds. For a diesel set the element is typically set at approximately 5 to 10 percent of rated power with a few seconds of delay.
Can a DG and a battery share load?
Yes, if both are on matched droop. A diesel governor typically runs at approximately 3 to 5 percent frequency droop, and setting the PCS to the same figure divides real power roughly in proportion to rating. What does not work is two sources both in isochronous mode: neither accepts a frequency error, so one takes everything while the other unloads or reverses.
Will a battery let me run with the generator switched off?
Only with a grid-forming PCS rated for the island load, enough usable stored energy for the run time, a starting arrangement the converter can survive, and island protection settings. A converter typically limits fault and inrush current to approximately 1.1 to 1.5 times rating, so the largest direct-on-line motor often sets its size rather than the average load.
Why do protection settings have to change in island mode?
Fault current in an island fed only by a converter is a small fraction of what the grid or an alternator delivers, so overcurrent elements graded for the grid-connected case may never pick up. The usual answer is a second settings group selected by a hard-wired contact from the island breaker, with earth fault and undervoltage elements carrying more of the discrimination.
Which interlocks must be hard-wired rather than left in software?
Source selection between grid, DG and coupler; the check-sync contact in the close circuit; the DG-running charge inhibit; the settings-group change on island transfer; battery DC isolation on a BMS or fire trip; the emergency stop; dead-bus arbitration; and the backstop behind any export limit. If its failure damages equipment or endangers a person, it goes in copper.
Do I need the utility's permission for closed-transition changeover?
Closed transition briefly parallels the plant with the grid, so it normally requires the distribution licensee's agreement and compliance with the applicable CEA regulations and the licensee's technical standard. Requirements for protection, settings approval and anti-islanding differ by licensee and connection voltage. Read the standard in force for your connection rather than copying a neighbouring plant.
Does adding storage mean replacing the existing panel?
Not usually, but sometimes. Replacement becomes the honest answer when the fault rating is marginal, when there is no design verification evidence for the assembly, or when the board is too full for the added relays, contactors and control supply load. A fault level check and a space and heat check at quotation stage settles it.
What should be proved at FAT before a storage retrofit goes to site?
Every row of the operating state table, simulated with auxiliary contacts: each permitted close, each blocked close, each source transfer, the charge inhibit with the DG running, the settings-group change on island transfer, and the emergency stop with the controller powered down. Each interlock should be deliberately failed to confirm the breaker does not close.
Related Guides
- DG synchronization panel working and load sharing
- AMF vs ATS vs DG synchronization
- 3-pole vs 4-pole ATS
- What a diesel generator costs per unit
- PCS full form and function
- The five EMS applications
- Product page: DG synchronization panel
- Service: Electrical balance of plant for solar and BESS
Talk to Us About Your Plant
Wisdom Techno Solutions manufactures the electrical system that sits at the centre of a solar and storage installation — the LT panel, the switchgear, the metering, the protection and the control — at our works in Vadodara, Gujarat. We build DG synchronization panel, and the same engineers who design an assembly test it before it ships and commission it on site.
Wisdom Techno Solutions is a licensed partner for three design-verified switchgear platforms: Rittal Ri4Power (Rittal Solutions Partner since 2021 — the Ri4Power system carries Intertek ASTA design verification to IEC 61439-1 and -2 Edition 3, with copper and aluminium busbar systems up to 6300 A), C&S CX (Licensed Partner since 2023, up to Form 4B Type II) and Siemens SIEPAN Elite/8PU (IEC 61439 Solutions Partner since 2024). We build to each system's verified configuration and routine-verify every assembly in-house at our Vadodara, Gujarat facility, for industrial, EPC and infrastructure projects across India. For a solar or storage plant that covers the LT switchboard, the BESS PCC and the AC and DC distribution.
If you want to know whether your plant is a candidate, send us twelve months of electricity bills and one day's load profile. That is enough to size a system, show where the savings would come from, and tell you honestly if the answer is no.
The quickest route is our free feasibility study: send the bills and we come back with the sizing and the numbers behind it. To work out your own numbers first, use the free DG replacement calculator.
Send your single line diagram, your load list or your last twelve bills, and we will come back with the electrical scheme and the numbers behind it.
Diesel synchronisation and changeover logic is engineered and tested at our LT panel manufacturer in Vadodara.